M3. The Sound Card's Clock
What It Is
The sound card counts samples by its own quartz crystal. If the crystal runs fast, the card’s second is short, and every beat seems to come a little late: the watch reads slow. The error is given in parts per million (ppm), + when the card runs fast.
| Card error | Rate error |
|---|---|
| 1 ppm | 0.09 s/d |
| 10 ppm | 0.86 s/d |
| 20 ppm | 1.73 s/d |
| 50 ppm | 4.32 s/d |
A sound card’s crystal is commonly 10 to 50 ppm off, and holds that error steadily. Two sound cards can read the same watch a few s/d apart.
How It Is Worked Out
A take’s readings are made on one clock, picked once from what the take has, in this order:
| Source | What it gives | |
|---|---|---|
| 1 | Clock log rated by USB lines | The log’s pauses and steps, with the USB lines’ steady error. |
| 2 | Clock log | Pairs of sound card time and computer time, written while recording. A fitted line follows drift and steps. |
| 3 | USB lines | A USB microphone picks up its computer’s bus, which sends a packet every millisecond. Faint lines at exact multiples of 1 kHz land in the sound, timed by the computer. Where they fall on the card’s clock gives the card’s error. |
| 4 | Known correction | One set for the take, or the one kept for that input by Quartz Correction. |
| 5 | None | The readings stay on the card’s clock. |
- Quartz Correction (Settings > Microphone, chapter 3) times the card against the computer’s clock while you listen, and offers to keep the error once it is known to half a ppm, after 20 minutes or more.
- The correction: a card
ppmfast makes rates read slow by aboutppm × 0.0864s/d. The app corrects exactly:(1 + rate/86,400) ÷ (1 − ppm × 10⁻⁶), less 1, times 86,400. - True time is the card’s time mapped through the take’s clock, with each pause’s length added. Every reading, window and hour is placed on it.
Why This Way
- The computer’s clock is kept right by internet time (NTP), so over minutes it is a far better reference than the card’s crystal.
- USB lines need no log, so a recording made in another app can still be corrected, if it came through a USB microphone.
- While you listen, the Rate card’s big figure stays on the card’s
clock, the clock other timegraphers and
timegrapher analyzeread on, so figures can be compared with theirs. The corrected rate is in the hover, as True Clock. - On an opened take with its own clock, from USB lines, a clock log that measured the card well enough, or a correction saved with it, the big figure is corrected, and the hover says by how much and from what source.
When You’d Use It
- Comparing takes from different microphones or computers: read the True Clock figures, or the error between them can be the cards'.
- Long takes and Power Reserve tests, where hours are counted: they are counted on true time.
- Checking a watch against a reference: only a corrected rate is comparable with a time signal or a certified figure.
What It Helps Find
- A rate difference that is the card’s, not the watch’s, between two setups.
- Pauses and sleeps in a long take, from the clock log.
- Disagreement between the USB lines and the clock log, by more than 5 ppm and 2 of the log’s standard errors, or between the USB lines and a kept correction by more than 5 ppm: the app says so in a caveat, since one of them is wrong.
What It Can’t Tell You
- Without a log, lines or a kept correction, nothing: the readings stay on the card’s clock, and the Rate card’s ? says the input’s clock isn’t measured.
- A busy computer delivers sound less evenly, so Quartz Correction’s offer can come later.
- The computer’s own error. On the stored takes, the USB lines and the internet-timed clock logs agree to about 1 ppm (0.1 s/d). A computer clock not kept by internet time carries its own crystal’s error into the log.
Previous: M2. Rate · Next: M4. Amplitude and Lift Angle
This page comes from the app's user guide at v1.0.1. See it on GitHub.